The Influence of Configuration Parameters of the Planetary Drive of Crank Presses on its Dynamic and Energy-Consumption Characteristics
DOI:
https://doi.org/10.15407/scine19.02.067Keywords:
planetary drive, transients, angular velocity, moments of inertia, and braking pointsAbstract
Introduction. The planetary drive has been widely found in the activation systems of crank presses as it improves working conditions of friction units and reduces press metal consumption and energy consumption.
Problem Statement. For studying the planetary motion of its main parts, it is advisable to consider its operation as four periods characterized by different patterns of changes in external loads and, consequently, different patterns of motion of core parts. The periods between switching the brakes when one link has not stopped, while other one starts moving is of the greatest interest. The problem of dynamic and energy-consumption parameters of the drive in transient conditions still remain a little open.
Purpose. The purpose of this research is to qualitatively assess the influence of configuration parameters on the dynamics of the processes of switching and stopping the planetary drive.
Material and Methods. The parameters of the experimental pilot plant, a model planetary drive with a nominal load of 400 kN, have been calculated. The minimum speed of the central gear has been estimated depending on the moments of inertia of the leading mass and the outer gear. The obtained dependences have been processed with the use of a standard mathematical apparatus.
Results. It has been found that the energy-consumption and dynamic parameters of the drive are significantly influenced by such characteristics as moments of inertia and braking moments, while decreasing angular velocity of the drive flywheel does not depend on the moments of inertia of the stopped links. The rate of braking processes is determined by the elastic properties of the friction materials and the parameters of the brake springs, not by the parameters of compressed air outflow.
Conclusions. The obtained analytical and graphical dependences have allowed not only qualitative, but also quantitative assessment of the influence of the parameters on the dynamics of processes. These recommendations can be used at the design stage, to select the optimal parameters of the drive with the predicted properties.
References
Baiul, K. V., Solodka, N. A., Khudyakov, A. Y., Vashchenko, S. V. (2020). Selection of rational surface configuration For roller press tires. Powder Metallurgy and Metal Ceramics, 59(1—2), 9—21. https://doi.org/10.1007/s11106-020-00133-w
Yavtushenko, A., Rudenko, A., Rybinok, V. (1980). Improvement of crank press activation systems. Kyiv [in Russian].
Belodedenko, S., Grechany, A., Yatsuba, A. (2018). Prediction of operability of the plate rolling rolls based on the mixed fracture mechanism. Eastern-European Journal of Enterprise Technologies, 1(7)(91), 4—11. https://doi.org/10.15587/1729-4061.2018.122818
Zhivov, L. І., Ovchinnikov, A. G. (1981). Forging and stamping equipment. Presses. Kyiv [in Russian].
Yavtushenko, A. V., Sereda, B. P., Vasilchenko, T. O., Glebenko, A. V. (2010). Approximate calculation of the main energydynamic parameters of the processes of switching on and stopping the planetary drive. Metal forming, 3, 175—179 [in Russian].
Vlasov, V. I. (1969). Systems for switching on crank presses. Moscow [in Russian].
Vlasov, V., Krupenko, A. G. (1971). Selection of the braking angle and parameters of the pneumatic control system based on safety conditions. Forging and stamping production, 12, 27—32 [in Russian].
Vasilchenko, T., Yavtushenko, G., Bondarenko, Y., Belokon, Y. (2015). Calculation of Planetary Drive of Mechanical Press. Metallurgical and Mining Industry, 7, 178—182.
Vasilchenko, T. А. (2013). Experimental studies of the planetary drive of crank presses. Bulletin of the National Technical University “KhPI”. Collection of scientific works. Series: new solutions in modern technologies, 11, 19—24 [in Russian].
Baiul, K., Khudyakov, A., Vashchenko, S., Krot, P. V., Solodka, N. (2020). The experimental study of compaction parameters and elastic after-effect of fine fraction raw materials. Mining Scince, 27. https://doi.org/10.37190/msc202701
Yavtushenko, A., Yavtushenko, G., Protsenko, V., Bondarenko, Y., Vasilchenko, T. (2019). Dynamics of Mechanical Press Drive. IEEE International Conference on Modern Electrical and Energy Systems (MEES), 2019. https://doi.org/10.1109/mees.2019.8896522
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Copyright Notice Authors published in the journal “Science and Innovation” agree to the following conditions: Authors retain copyright and grant the journal the right of first publication. Authors may enter into separate, additional contractual agreements for non-exclusive distribution of the version of their work (article) published in the journal “Science and Innovation” (for example, place it in an institutional repository or publish in their book), while confirming its initial publication in the journal “Science and innovation.” Authors are allowed to place their work on the Internet (for example, in institutional repositories or on their website).
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
